|
|
 |
|
Chicken Feed Pellet Mill Machine
6MM |
|
|
|
|
|
|
|
Feed granulator
is widely used in large, medium and small aquaculture, grain feed
processing plants, livestock farms, poultry farms, individual farmers,
small and medium-sized farms and large, medium and small feed processing
plants.
This machine can
be used alone, and customers who need it can also match it with a straw
cutter for better results. |
|
Note:
1. Before using the
machine, it is necessary to adjust the screw of the pressure roller to
the appropriate position. The pressure roller and the pressure plate
should be closely combined, and the two adjusting screws should be on
the same horizontal plane.
2. Please refuel the fuel
tank before using the machine. The machine should not idle for more than
2 minutes.
3.Double-check the belt
and the screws before operation.
4.After using the machine, clean up the rest to prevent damage to the
machine.
5.If the pressure roller cannot rotate normally, please tighten the
screws that control the pressure roller first, and then try to power it
on. If it still does not work, you can appropriately loosen the screws
next to the pressure roller and then tighten them slightly again
(without special tightening)
|
|
Product parameter: |
 |
| Pressure plate: |
6MM |
| Output/h |
200-250KG |
| Power: |
7.5KW |
| Voltage: |
220V Three-phase electricity |
| Product body material: |
Cast iron |
| Standard pressure roller: |
Two-head press roller |
| Product size: |
39.56*14.17*36.8in(100.5*36*93.5cm) |
|
|
Product analysis: |
 |
|
Feature: |
 |
This machine is equipped with an
enlarged and widened discharge port to prevent feed from splashing and
facilitate the feed collection conducted by customers. |
|
The machine is equipped with mobile
wheels for easy handling and movement. |
 |
 |
The adjustable nut is used to
adjust the distance between the pressure roller and the grinding disc.
When making pellets, the nuts on the two sides must be balanced to
avoid damage to the pressure roller and grinding disc.
If the pressure roller cannot rotate normally, please tighten the screws
that control the pressure roller first, and then try to power it on. If
it still does not work, you can appropriately loosen the screws next to
the pressure roller and then tighten them slightly again (without
special tightening) |
|
Enlarge the feed inlet
The machine adopts the design of
enlarged feed port, which makes it more convenient for you to feed raw
materials and
effectively improves work efficiency. |
 |
 |
Here is the filling port, open here to
add engine oil It is
recommended to add high-quality machine oil or hyperbola heavy-duty gear
oil.（The color of the oil filling plug is random） |
|
The length of feed particles can be
adjusted here. |
 |
 |
After using the machine for a period of
time, the customer needs to add lubricating oil here to lubricate the
grinding chamber (approximately 4-6 months of use) (the lubricating oil
gun and lubricating oil need to be purchased by the customer themselves,
we do not provide them). |
|
The voltage display meter can clearly
show the voltage, making it convenient for customers to distinguish the
correct voltage. |
 |
|
|
Powder can leak out here to prevent
powder from accumulating in the grinding chamber. |
 |
 |
|
Precautions:
|
|
1.When using, it
should be noted that there should be no foreign matter such as stones
and iron blocks in the raw materials. After the pellet machine has been
working continuously for more than ten shifts, the pressure roller oil
hole, the universal joint oil hole, and the linkage shaft oil hole need
to be filled with high-temperature lubricating grease to make the
pressure roller have good working performance and extended bearing life.
2.During granulation, it is strictly forbidden for the pressure roller
to make contact with the template to run idly, and the continuous feeding can
not be interrupted.At the same time, the pressure roller shaft nut is
locked to avoid loosening and damaging the spindle keyway.
3.When granulating, there is no granulation and no discharge, the
template should be removed, and after opening one by one, some fiber feed
can be added appropriately to restart the granulation.
4.Always check
the tightness of the screws in each part of the machine. If there is oil
leakage in the gearbox, replace the oil seals in time, and check whether
the bearings in the machine head are short of oil.
5.When the pellet machine is working, do not reach into the feeding
port with your hands. If necessary, use wooden sticks to help feed the
pellets.
6.Before turning on the machine, it is necessary to add less
materials. When shutting it down, leave a small amount of feed in the
machine to prevent the press roller of the machine from contacting the
template to idle.
7.If the machine is stuck in operation, stop it immediately, press the
pressure roller until the bolt is flat,and then restart the machine.
8.Each time the work is completed, the adjusting pressure roller bolts
must be loosened.
9.Iron or stones cannot be put into the machine.
10.Check the elasticity of the belt, and the bearing frequently. Add oil
in time when it needed.
|
|
Note:
We suggest that
high-power machines should be directly connected to the main power
supply, as the voltage reaching the machine is stable. If the voltage is
unstable and the current exceeds the rated current of the motor, it is
easy to burn out the starting capacitor.
It is recommended to
directly connect the machine to the power supply as much as possible. If the machine
is not connected to the power supply, different situations may occur,
and the wires are not durable. The wires will gradually burn out over
time.
Our machine is not
equipped with a plug. If you do not know how to operate the wiring
, you can contact our customer service and we will provide you with the
wiring video.
|
 |
|
Details: |
 |
 |
|
Usage and specification:
|
|
1: It applies to chicken industry.
2:Corn particles can be put into the machine
directly. The feed processed by the machine is smooth and has moderate
hardness. The temperature change in the process is slight so the
nutrition can be maintained very well.
3:The practical diameter of the holes can be
divided into: Φ2, Φ3, Φ4, Φ5, Φ6, Φ8,
Φ10, Φ12.
4:The microorganism and parasite can be killed by
extrusion in the process.
|
|
Operating principle and product
advantages: |
|
Small feed
granulator, also known as small household feed granulator, is based on
the principle of circular motion. The template and pressure roller are
made of high-quality chrome-manganese titanium and are specially
treated. The main shaft and flat mold drive the pressure roller to
rotate under the action of friction. The materials are gelatinized
between the pressure roller and the template at high temperature. The particles are discharged from
the mold hole under the extrusion of the pressure roller. The particles
made are sent out of the machine through the throwing plate, and the
length of the particles can be adjusted through the notch.
This product
model is a new energy-saving product. In the past, the feed was usually
processed into powder and then fed, which had some defects such as
inconvenient feeding, poor palatability, picky eating of livestock, and
low utilization rate. With the advent and popularization of new small
pellet feed machinery, powder feed can be easily processed into pellet
feed. Lighting electricity can be used as the power to press granules from the die hole under the extrusion of the press roller,
which can easily adjust the length of the granules. Its structure is
simple, occupied area is small, the noise is low, and it has many
advantages raw materials are processed into pellet feed.
|
|
Product display: |
 |
 |
|
Item Number:
1*Chicken Feed Pellet Mill Machine 220V (238008) |
|
|
You can make order
with no worry.
Any concerns just feel free to let us know, we'll reply in 24 hours in
normal condition.
Handling Time: Shipping is usually made in 1-3 business days after
payments cleared. Orders are processed from Monday-Friday; Not on the
weekends & public holidays.
Warranty: 6 months' warranty for the machines, not for the consumables.
We stand behind our products all the item, so even if your warranty
period has expired, you can still seek for service or technical support
from us with low cost. |
|
