|
|
 |
|
220V Rocker
Arm/Foldable Arm Curved Edge Banding Machine |
|
|
|
|
|
|
 |
|
Product
Overview |
|
The rocker arm curved edge
banding machine is a special device for edge banding of boards in
different shapes, the functions of edge banding, timing strip breakage,
powerful suction, auxiliary hot air and so on can be fulfilled on one
machine, the operating difficulty and complexity are greatly reduced,
and the edge sealing performance, the attractiveness and the durability
of boards can be well improved. The machine can be widely applied to the
industries of cabinet manufacturing, wooden door production, home
customization and so on. |
|
Product
Parameters |
|
Model |
F11-3 |
|
Voltage |
220V 50Hz Single-phase electricity |
|
Total power |
3.8Kw |
|
Air pressure |
0.6-0.8Mpa |
|
Edge Strip width |
14-70mm |
|
Edge Strip thickness |
0.5-2mm (related to edge strip materials) |
|
Edge banding speed |
0-24cm/s |
|
Edge band materials |
PVC, veneer, melamine, plastic, etc. |
|
Board shape |
Circular boards, square boards, triangular
boards, L-shaped boards, etc. |
|
Board size |
Circular board≤1.6m,Square
board≤1x1.5m, L-shaped board≤1.2x1.2m |
|
Applicable boards |
Plywood boards, acrylic boards, chipboards, block
boards, density boards, etc. |
|
 |
|
Operation
Instructions |
 |
|
Temperature Regulation
Firstly, adjust the temperature until the hot melt glue has
slight smoke, and then reduce the temperature by 5-10 degrees
every 5-10 minutes. When the machine is used for the first time
or each time another hot melt glue is replaced, the temperature
must be reset. When the temperature reaches the set temperature,
the motor can be started.
|
|
Motor Control
When the temperature reaches the set temperature, the motor can
be started. The motor may be overheated when the speed is below
30 for a long period of time. The edge banding speed can be
0-24cm/s.
|
|
|
Attention |
|
1. The machine
must be reliably grounded. |
|
2. Please check
the amount of the remaining hot melt glue in the glue pot before use. |
|
3. When any
abnormal situation occurs in the working process, please press the
emergency stop switch immediately. |
|
4.
Non-professionals are prohibited from operating and repairing the
machine. |
|
5. When
disassembling and repairing the machine, first turn off the power and
then wear protective tools. |
|
6. When inspecting the circuit, be sure
to completely disconnect the power supply, otherwise there is still
electricity in the circuit! |
|
7. The machine
needs to be connected with an air compressor which needs to be prepared
by the customer. |
|
8. Keep hands, clothing
and tools away from moving parts while the machine is in operation. |
|
Operation Method |
|
1. Fix the machine to the horizontal
position firmly and stably.
2. Connect the machine to the 220V power supply with the leakage
protector, and pay attention to connecting the ground wire.
3. Connect the air source to the oil-water separators.
4. Add the appropriate amount of hot melt glue to the glue pot.
5. Place the edge banding strip and adjust the height limit column.
6. Adjust and lock the fitting wheel as needed.
7. Set the temperature through the temperature regulator, adjust the
motor speed through the motor speed regulator, and start the motor after
the temperature reaches the set temperature and the red light of the
temperature controller is on.
8. Place the board on the suction disc, push the board to be subjected
to the edge banding operation through the foot pedals.
|
|
Product
Features |
 |
|
Foldable Arm & Suction Disc
The suction disc has the high suction so that the board can be
firmly sucked onto the suction disc and prevented from being
suspended in the air or falling off. Meanwhile, along with the
flexible movement of the foldable arm, the board on the suction
disc can be pushed to be subjected to edge banding operation.
The foldable arm can be folded and unfolded at any during the
edge banding operation, time and labor are greatly reduced, and
the practicability is greatly improved.
|
|
Control Panel
The multifunctional control panel is designed for the machine
and can fulfill multiple functions, such as power supply,
emergency stop, temperature regulation, motor speed regulation
and curve timing. The user can accurately control and adjust
different parameters according to board processing requirements.
Digital display is clear and obvious, and the production
efficiency can be obviously improved.
|
|
Oil-water Separators
The machine is equipped with two oil-water separators, one
oil-water separator is used for controlling the cutter and the
strip moving plate, and the other is used for controlling the
suction disc. The two oil-water separators control different
parts correspondingly and ensure the accurate air pressure and
smooth operation. The oil-water separators should be adjusted
before edge banding operation is conducted.
|
|
 |
|
Auxiliary Hot Air Device
The device can be used for heating and softening the edge
banding strip so that the edge banding strip and the board can
firmly glued together. The outlet air angle can be adjusted
freely and flexibly by loosening and tightening the nut. The
edge banding strip is not prone to be separated from the board,
the edge banding effect can be well improved, and the bonding
firmness can be higher.
|
|
Glue Coating Part
The heightened glue coating assembly adopts a
high-temperature-resistant bearing and sealing rings, achieves
single-sided glue coating of the edge banding strip, thereby
saving the hot melt glue and being small in glue line. The
2800ml large-capacity glue pot avoids frequent addition of the
hot melt glue, thereby greatly reducing the labor intensity. The
lengthened knob facilitates the glue quantity adjustment, and
operation is more convenient and easier.
|
|
Dual Foot Pedals
The design of double foot pedals is adopted, one foot pedal can
control the suction of the suction disc, and the other foot
pedal can control strip feeding and breakage of the edge banding
strip. Two hands of the user are liberated, the functions are
clear and accurate, the operating complexity and difficulty are
greatly reduced, and the user experience is good.
|
|
 |
|
Strip Moving Plate
The novel strip moving plate can prevent the edge banding strip
from moving in the reverse direction, and the edge banding strip
can be fed stably and smoothly and is not prone to deviation.
The strip moving plate facilitates feeding movement of the edge
banding strip and well assist in edge banding operation.
|
|
Cutter Assembly
The cutter assembly can make a very quick response and ensures
the cutoff perpendicular precision. The cutter is stable through
the double column balance, the structure is compact, and the
cutoff flatness and the cutting effect are good. The maximum
strip cutting width can be 70mm, and the maximum strip cutting
thickness can be 2mm.
|
|
Double Cylinders
Two cylinders are installed to fulfill different function
control. One cylinder is used for controlling the cutter, and
the other cylinder is used for controlling strip feeding
operation. Independent control of different motions can be
achieved by the cylinders, the control precision is high, and
the control effect is good.
|
|
|
Application |
|
The rocker arm curved edge
banding machine can be used for processing various boards in different
shapes, can stick different edge banding strips such as PVC strips,
plastic strips and melamine strips to the boards, can be widely applied
to woodworking plants and workshops and has a good edge banding effect. |
 |
|
Product
Display |
 |
 |
|
Item Number (154069):
1 x Rocker Arm/Foldable Arm Curved Edge Banding Machine 220V |
|
|
You can make
order with no worry.
Any concern just feel free to let us know, we'll reply in 24 hours in
normal condition.
Handling Time: Shipping is usually made in 1-3 business days after
payments cleared. Orders are processed from Monday-Friday; Not on the
weekends & public holidays.
Warranty: 6 months' warranty for the machines, not for the consumables.
We stand behind our products all the item, so even if your warranty
period has expired, you can still seek for service or technical support
from us with low cost. |
|
